Detailed instructions for use are in the User's Guide.
[. . . ] DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. When using the projector in Europe COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" and 73/23/ EEC "Low Voltage Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. [. . . ] Caution: · When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically.
The volume from the speaker Press the VOLUME + or button to change the volume from the speaker. · The volume control bar will disappear about 4 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. · The volume from the AUDIO OUT jack is also changed by pressing the VOLUME + or button on the remote control.
EN 14
Menu operation
IMAGE
COLOR TEMP
TINT *2, *5 *5 COLOR SHARPNESS *5 INSTALLATION AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE MENU POSITION EXPAND MODE VIDEO MODE *5 CINEMA MODE *5, *6 VIDEO SIGNAL *5 LANGUAGE RESET ALL SIGNAL HORIZ. POSITION VERT. POSITION TRACKING *4 FINE SYNC. *4 COMPUTER INPUT *4 ANAMORPHIC *4 HOLD
ON, OFF OFF, 5, 10, 15, 30, 60 min ON, OFF BLUE, BLACK OFF, MIRROR, INVERT, MIRROR INVERT UPPER LEFT, LOWER RIGHT EXPAND, REAL 1-4 AUTO, OFF AUTO, NTSC, PAL, SECAM, 4. 43NTSC, PAL-M, PAL-N, PAL-60 , English, Español, Deutsch, Français, Italiano, OK 0 - 999 *3 0 - 999 *3 0 - 9999 *3 0 - 31 RGB, YCBCR / YPBPR ON, OFF ON OFF OK
FEATURE
BEGIN END CLAMP POSITION *4 CLAMP WIDTH *4 VERT. SYNC SHUTTER (U) SHUTTER (L) SHUTTER (LS) SHUTTER (RS)
0 - 15 0 - 15 0 - 127 *3 0 - 63 *3 AUTO, OFF 0 - 20 0 - 20 0 - 20 0 - 20
USER
* 1: The item can not be selected when the sRGB is set to ON. Select MIRROR, INVERT in rear projection with the projector hanging from the ceiling.
ON
3 FEATURE MENU POSITION . . . . . Use to select the position of the menu on the screen, UPPER LEFT or LOWER RIGHT. · Though square-shaped noise may appear in the projected image when 1 is selected, this is not failure. · A playback signal on a deteriorated videotape or a poor-quality signal may not be projected properly. When projecting such a signal, change the setting of the Video mode and check the projection quality.
Opt
TV60
FEATURE MENU POSITION UPPER LEFT EXPAND 1 AUTO AUTO English OK
A
A
EXPAND MODE VIDEO MODE CINEMA MODE
?
VIDEO SIGNAL
A Ë LANGUAGE RESET ALL
EN 16
CINEMA MODE . . When ON is selected, the film mode will be automatically activated when a film source signal is inputted. When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn't displayed correctly, select the desired video format manually. ( / English / Español / Deutsch / Français / Italiano / ) RESET ALL . . . . . . . . Use to synchronize the projector with PC input signals so that the image is not blurred. This will be set automatically to match the input signal to component video (YCBCR/YPBPR) or RGB. [. . . ] Contact your dealer for details.
1) Interface
PROTOCOL BAUD RATE DATA LENGTH PARITY BIT STOP BIT FLOW CONTROL RS-232C 9600 [bps] 8 [bits] NONE 1 [bit] NONE
3 6 12
1 RXD (IN: on the Projector side) 4 GND 7 TXD (OUT: on the Projector side)
79
This projector uses RXD, TXD and GND lines for RS-232C control. For RS-232C cable, the reverse type cable should be used.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the command is different by each function.
HEX ASCII Address code 30h 30h '0' '0' Function code Function Function Data code Data Data End code 0Dh
[Address code] [Function code] [Data code] [End code]
30h 30h (In ASCII code, '0' '0') fixed. 0Dh (In ASCII code, ' ') fixed.
1
3) Control sequence
(1) Send the command from a personal computer to the projector. [. . . ]