User manual ACER V243HQL

[. . . ] RGB IN port Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor. Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The appearance and locking method may differ from the illustration depending on the manufacturer. Note The location of the Kensington Lock may be different depending on its model. Using the Anti-Theft Kensington Lock 1. [. . . ] · Connect the monitor to the Macintosh computer using the D-sub connection cable. Note If the monitor and the computer are connected, you can turn them on and use them. Connections Using the Stand Monitor Assembly Monitor and Bottom Folding the base Note You can tilt the monitor upwards at an angle of -1° to 21°. Troubleshooting Troubleshooting {T200N, T200GN, V243HQL, T220GN } Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. Troubleshooting Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. A: Windows ME/2000 : Set the resolution at the Control Panel Display Settings. Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found" Q: A: Q: A: Have you installed the monitor driver?Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Install the monitor driver according to the Driver Installation Instructions. Check when MagicTuneTM does not function properly. Q: MagicTuneTM feature is found only on PC (VGA) with Window OS that supports Plug and Play. Troubleshooting A: To check whether your PC is available for MagicTuneTM feature, follow the steps below (When Windows is XP); Control Panel Performance and Maintenance System Hardware Device Manager Monitors After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. A: MagicTuneTM is an additional software for the monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www. samsung. com/monitor/magictune MagicTuneTM doesn't work properly. Q: A: Have you changed your PC or video graphic card?The program can be downloaded http://www. samsung. com/monitor/magictune Did you install the program?If a copy of the program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program. [. . . ] (If it does, request an a service for the main board of the computer. ) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution. ) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note If problems repeatedly occur, contact an authorized service center. Troubleshooting {T200N, T200GN, V243HQL, T220GN } Q&A Q: A: A: Q: A: How can I change the frequency? [. . . ]