User manual ASUS T3-M3N8200 T-M3N8200 INSERTPAGE(ENGLISH)
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ASUS T3-M3N8200. We hope that this ASUS T3-M3N8200 user guide will be useful to you.
You may also download the following manuals related to this product:
ASUS T3-M3N8200 T-M3N8200 USER’S MANUAL(JAPANESE) (4942 ko)
ASUS T3-M3N8200 T-M3N8200 SERIES USER’S INSERTPAGE (JAPANESE) (554 ko)
ASUS T3-M3N8200 T SERIES-M3N8200 USER’S MANUAL(ENGLISH) (3583 ko)
Manual abstract: user guide ASUS T3-M3N8200T-M3N8200 INSERTPAGE(ENGLISH)
Detailed instructions for use are in the User's Guide.
[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe.
ii
Table of contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the 4-pin power plug to the power connector of the IDE hard disk drive, or the Serial ATA hard disk drive with a 4-pin power plug. For Serial ATA hard disk drive without a 4-pin power plug, connect the 15-pin SATA power adapter plug to the power connector at the back of the drive, then connect the other end (4-pin male) to a 4-pin (female) power plug from the power supply unit.
See the Appendix for the power supply specifications.
REAR SPK
CTR BASS
SIDE SPK
Voltage selector
The PSU has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area.
NOTE. The voltage selector is set to 230 V by default.
MIC IN FRONT LINE IN
If the voltage supply in your area is 100-127 V, set the switch to 115 V. If the voltage supply in your area is 200-240 V, set the switch to 230 V.
Setting the switch to 115 V in a 230 V environment will seriously damage the system!
eSATA
2-20
Chapter 2: Basic installation
2. 11
1. 2.
Replacing the cover
3 2
To replace the cover: Turn the chassis upright. Position the front edge of the cover at least two inches from the front panel cover. Push the cover slightly toward the front panel until it fits in place. 4.
4
5.
3
4
2
ASUS T3-M3N8200
2-21
2-22
Chapter 2: Basic installation
Chapter 3
This chapter helps you power up the system and install drivers and utilities from the support CD.
Starting up
3. 1
Installing an operating system
The barebone system supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information.
3. 2
Powering up
The system has one power buttons located on the front panel. · The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode.
+5V (Default)
23
+5VSB
+5V (Default)
2.
Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 500 mA on the +5VSB lead, and a corresponding setting in the BIOS.
KBPWR
12 23 +5VSB
R
+5V (Default)
M2N5-BN
M2N5-BN Keyboard Power Setting 4-4 Chapter 3: Starting up
4. 4
1.
Connectors
This section describes and illustrates the connectors on the motherboard. CPU fan connector (4-pin CPU_FAN) The fan connector supports the proprietary CPU fan. Connect the fan cable to the fan connector on the motherboard, making sure that the black wire of the cable matches the ground pin of the connector.
R
CPU_FAN
CPU FAN PWM CPU FAN IN CPU FAN PWR GND
M2N5-BN
M2N5-BN CPU Fan Connector
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow within the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors!
ASUS T3-M3N8200
4-5
2.
ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for the 24-pin and 4-pin power plugs from the power supply unit. The plugs from the power supply unit are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
Do not forget to connect the 4-pin ATX12V power plug to the ATX12V connector on the motherboard; otherwise, the system will not boot up. EATXPWR
+3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts
R
M2N5-BN
M2N5-BN ATX Power Connector
4-6
GND +12V DC
GND +12V DC
ATX12V
Chapter 3: Starting up
3.
Serial ATA connectors (7-pin SATA1, SATA2, SATA3) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
SATA2
GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND
SATA1
R
M2N5-BN
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND
SATA3
GND RSATA_TXP3 RSATA_TXN3 GND RSATA_RXP3 RSATA_RXN3 GND
M2N5-BN SATA Connectors When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1/2 connector. Refer to the table below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Connector Color Setting Use
SATA1 SATA2/3
Black Black
Master Slave
Boot disk Data Disk
right angle side
Connect the right-angle side of SATA signal cable to SATA device. [. . . ] Confirm the password when prompted.
The message "Password Installed" appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message "Password Uninstalled" appears.
ASUS T3-M3N8200
5-29
If you forget your BIOS password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ASUS T3-M3N8200
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ASUS T3-M3N8200 will begin.