User manual PHILIPS 32PFL5606H

[. . . ] Register your product and get support at www. philips. com/welcome 47PFL4606H 46PFL5606H 42PFL4606H 42PFL4506H 42PFL3x06H 40PFL56x6H 37PFL4606H 32PFL5x06H 32PFL4606H 32PFL3x06H DesignLine Tilt EN User manual 1 2 3 Notice Important Your TV TV controls Remote control Remote control usage 2 4 7 7 8 9 10 10 10 11 11 12 12 13 14 14 14 14 15 15 18 19 20 20 21 22 23 24 24 25 27 27 29 29 29 7 Connect devices Back connections Side connections Connect a computer Use a Conditional Access Module Use Philips EasyLink Use a Kensington lock 4 Use your TV Switch your TV on Switch your TV to standby Switch your TV off Switch channels Watch connected devices Adjust TV volume Use teletext 33 33 35 36 37 38 40 41 41 41 41 41 41 42 42 44 44 44 44 45 45 45 45 46 8 Product information Supported display resolutions Multimedia Tuner/Reception/Transmission Remote control Power Supported TV mounts Product specification 5 Use more of your TV Access TV menus Add device to the home menu Rename devices from the home menu Remove devices from the home menu Change picture and sound settings Use the universal access menu Use advanced teletext features Create and use lists of favourite channels Use the Electronic Programme Guide Display the TV clock Use timers Lock unsuitable content View Scenea Change language Play photos, music and videos on USB storage devices Listen to digital radio channels Update the TV software Change TV preferences Start a TV demo Reset the TV to factory settings 9 Troubleshooting General TV issues TV channel issues Picture issues Sound issues HDMI connection issues Computer connection issues Contact us 10 Index EN 1 English Contents 6 Install channels Automatically install channels Manually install analogue channels Manually install digital channels Rename channels Rearrange channels Hide channels Unhide channels Access CAM services 30 30 31 31 31 32 32 32 32 1 Notice 2011 © Koninklijke Philips Electronics N. V. Trademarks are the property of Koninklijke Philips Electronics N. V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system. [. . . ] Dual sound broadcasts: With digital broadcasts, you can select a subtitle language. Switch on Scenea 1 2 Press . Change menu language Select [Scenea], then press OK. » If a customised Scenea picture is loaded, that picture is displayed (see `Customise the Scenea picture' on page 24). 1 2 3 Press . Select [Setup] > [TV settings] > [Preferences] > [Menu language], then press OK. Select a language, then press OK. Change audio language You can choose an audio language if it is available from your broadcaster. For analogue channels, two languages may be available. Customise the Scenea picture You can load another picture as the wallpaper. Note · When you load a new Scenea picture, it overrides the · To use another picture as the wallpaper, you need a current Scenea picture. USB storage device that contains a picture that is less than 1 MB in size. 1 2 3 While you watch TV, press OPTIONS. For digital channels, select [Audio language], select the language, then press OK. For analogue channels, select [Dual I-II], select either language, then press OK. 1 2 3 4 5 6 7 Load a picture smaller than 1MB in size into a USB storage device. Press any button to exit Scenea. Show or hide subtitles 1 2 While you watch TV, press SUBTITLE. · [On during mute]: When audio is muted, display subtitles. Note · Repeat this procedure to enable subtitles on each · Select [Subtitles] > [Subtitles off] to disable subtitles. 24 EN analogue channel. Note · When you select a subtitle language in a digital TV channel as described below, the preferred subtitle language set in the installation menu is temporarily overruled. · 1 2 3 4 While you watch TV, press Select a subtitle language. · Select [Subtitle language], then press OK. Press the following buttons to control play: · to play. To return, press . Change slide show settings Play photos, music and videos on USB storage devices Caution · Philips is not responsible if the USB storage device is not supported, nor is it responsible for damage or loss of data from the device. 1 2 While you view a slide show, press OPTIONS. · [Slideshow transitions]: Set the transition from one picture to the next. · [Slideshow frequency]: Select the display time for each photo. · [Repeat] / [Play once]: View the pictures in the folder once only, or repeatedly. · [Shuffle off] / [Shuffle on]: View the pictures in sequential order, or at random. · [Show info]: Display the picture name, date, size and next picture in the slide show. · [Set as Scenea]: Set the selected picture as the TV wallpaper (see `View Scenea' on page 24). To return, press Note Connect a USB storage device to play photos, music or videos stored on it. 1 2 3 4 Switch on the TV. » The USB browser appears. View photos 1 2 In the USB browser, select [Picture], then press OK. Select a photo or a photo album, then press OK to view the photo enlarged to fill the TV screen. To return, press . 3 . 3 · [Rotate image] and [Show info] appear only when the slideshow is paused. EN 25 English Select a subtitle language in digital channels View a slide show of your photos 1 When a full screen image of a photo is displayed, press OK. » A slide show begins from the selected photo. Listen to music 1 2 3 Change video settings · While you play video, press OPTIONS to access one of the following settings, then press OK. · [Full screen] / [Small Screen]: View the video stretched to fill the screen, or view it in its native picture format. [. . . ] The picture does not fit the screen; it is too big or too small: · Try using a different picture format. The picture position is incorrect: · Picture signals from some devices may not fit the screen correctly. Check the signal output of the device. HDMI connection issues There are problems with HDMI devices: · Note that HDCP (High-bandwidth Digital Content Protection) support can delay the time taken for a TV to display content from a HDMI device. · If the TV does not recognise the HDMI device and no picture is displayed, try switching the source from one device to another and back again. [. . . ]