User manual PHILIPS 4 FUNCTION UNIVERSAL REMOTE

[. . . ] Or as an alternative, you can use the Auto Scan feature, on page 5, to program your component codes. The following chart lists the remote component keys and what type of device each key will control: 12 ENTER Use ENTER once after entering channel numbers on some TV models. 5 VOL Keys Use VOL+ (or VOL-) to raise (or lower) the sound volume. 13 VCR Transport Keys Use the VCR Transport Keys to control your VCR. Press REC twice to record a tape. 6 POWER Key Press POWER once to turn on or off the selected home entertainment component. Key TV VCR CBL AUD Programmed to Control TV VCR or DVD Cable Box Amplifier/Receiver 14 TV/VCR Press TV/VCR once to view VCR playback or TV through the VCR. 7 MUTE Key Press MUTE once to turn sound off or on. 15 FAV CH Key Use to pre-program up to 10 favorite channels. NOTE: If you want the component keys to control other types of devices, you'll need to reassign the component keys. IMPORTANT: Please completely read and review the following steps before proceeding. [. . . ] Press and hold SET until the red light blinks twice, then release SET. When re-assignment is done, the red light will blink twice to confirm your choice. The AUD key is now ready to be programmed for your DVD (or VCR) player. See Programming Your Remote Control on page 4. If SCAN is pressed again after any key stops Auto Scan, the remote will continue Auto Scan of the next ID from where it stopped. If you have passed by the code that turns off the TV, press VOL- one or more times until the TV turns on again. To lock in the code and exit Auto Scan, press and release SET the red light will blink twice. To search for codes of other components, repeat steps 2 through 5, but substitute the appropriate key (e. g. , VCR, CBL) for the (VCR or Cable) component you are searching for. ABOUT OTHER FEATURES Volume Lock The remote control is set at the factory to control the volume independently while in the TV, VCR, and CBL modes. g. , TV) while in another mode (e. g. , VCR or CBL), perform the instructions below to lock the volume setting. This procedure will not affect separate control of your audio component's volume in the AUD modes. NOTES: In the search mode, the remote will send IR (infrared) codes from its library to the selected device, starting with the most popular code first. Checking the Auto Scan Codes If you have set up the remote control using Auto Scan, you can now find out which four-digit code is operating your component: 1. On the remote control, press a component key once (e. g. , TV, VCR, CBL or AUD). Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. NOTE: By pressing AUD before entering the sequence below, the remote control will operate your home theater volume controls in all modes. This feature does not apply to component keys that have been re-assigned. 1. Press and hold SET until the red light blinks twice, then release SET. The SCAN key allows the remote control to scan the TV, VCR and CBL channels. When activated, the remote control will change channels every 3 seconds. Scanning will start with the current channel, then proceed to the next channel up, and continue until all channels of your TV, VCR or CBL component are scanned. To stop scanning channels, press SCAN. NOTE: If a code digit is "0" , the red light will not blink. 5. Use 2 for the second digit, 3 for the third digit and 4 for the fourth digit. To find codes of other components, repeat steps 1 through 5, but substitute the appropriate key (e. g. , VCR or CBL) for the component you are checking. As before, write down each four-digit code. 6. 3. Re-Assigning Component Keys The remote can be set up to control any combination of four home entertainment components. By following these instructions, you can re-assign or duplicate a component key onto an unused component key. [. . . ] Press component key Press component key to be moved once to be reassigned once (e. g. , VCR). Reassigned key is now ready for programming. 1 2 3 4 7 8 TROUBLESHOOTING PROBLEM: Red Indicator Light does not blink when you press a key. SETUP CODES FOR TELEVISION SOLUTION: CÓDIGOS DE PROGRAMACIÓN PARA TELEVISIÓN CODES DE PROGRAMMATION DU TÉLÉVISEUR Replace the batteries with two (2) "AA" alkaline batteries (see Page 3). The VOL+, VOL- and MUTE keys are not functional. Make sure that the volume control is locked to a component that has volume capabilities and is programmed into the remote control. Red Indicator Light blinks when you press a key, but home entertainment component does not respond. Make sure you are aiming the remote control at your home entertainment component and that you are within 15 feet of the component you are trying to control. The remote control does not control home entertainment components or commands are not working properly. Try all listed codes for the component brand being set up. Make sure all components can be operated with an infrared remote control. CH+, CH- and LAST do not work for your RCA TV. Due to an RCA design (19831987), only the original remote control will operate these functions. A-Mark AOC Admiral Adventura Aiko Akai Alaron Ambassador America Action Ampro Anam Anam National Archer Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Clairtone Concerto Contec Craig Crosley Crown Curtis Mathes Changing channels does not work properly. If original remote control required pressing ENTER to change channels, to change channels, press ENTER on the remote after entering a channel number. Tried Auto Scan and still could not find a working code. Try Auto Scan again after clearing out the component key as follows: Press and hold SET until Red Light blinks twice, then release. Then press and release the component key to be cleared twice. Daewoo Daytron Denon Dumont Dwin Electroband Emerson NOTE: To clear all set up codes and restore functions to Default, press SET until red light blinks twice, release SET and enter 9-8-1. [. . . ]