User manual PHILIPS RI 9722

[. . . ] , 1&$172 6&/$66 INCANTO rondo INCANTO classic INCANTO de luxe INCANTO sirius Revision: 1 IURP SDJH WR SDJH , 1&$172 INCANTO easy INCANTO INCANTO rapidsteam INCANTO digital INCANTO digital SBS Revision: 5 IURP SDJH WR SDJH SERVICE MANUAL Saeco Saeco International Group All parts of the present service manual are the pro perty of Saeco International Group. The manufacturer is not responsible for any errors or omissions in t he present document. Any reproduction or unauthoris ed use of this manual without the prior written permission of the manufac turer or by contractual agreement is prohibited. INCANTO S-CLASS INCANTO rondo INCANTO classic INCANTO de luxe INCANTO sirius SERVICE MANUAL Revision: 1 Saeco Saeco International Group FEB. : 2005 All parts of the present service manual are the property of Saeco International Group. The manufacturer is not responsible for any errors or omissions in the present document. [. . . ] 8 · Assembly in reverse order Seite 6/29 REV. 1 FEB. 2005 Saeco International Group INCANTO-CLASS 4. DISASSEMBLY · · Insert the ringnut in the same position where its been removed. Press the release button and turn it clockwise till the two reverence marks match. Fig. 1 · When attaching the bean hopper ensure, the third small dot of the adjustment knob and the reverence pin are matching. Fig. Disassembly of the grinder INCANTO S-CLASS · Cut the relevant clips. Fig. 3 Seite 8/29 REV. 1 FEB. 2005 Saeco International Group INCANTO-CLASS 8. DISASSEMBLY · Remove the four screws, as shown in figure 4 Fig. 4 · Remove the sensor, by pressing the anchoring tab by means of a screwdriver. . . . . . . . . . Fig. 5 · . . . . . . . . at the same time remove it from its seat. Fig. DISASSEMBLY INCANTO S-CLASS · Fit the rubber cap to the flange of the new grinder motor. Fig. 8 · Fit the rubber cap to the flange of the new grinder motor. Fig. 9 · Insert the sensor removed from the old grinder motor, or if necessary a new sensor into its seat. Fig. 10 · Firmly insertit till the anchoring tab locks the sensor. Fig. 11 Seite 10/29 REV. 1 FEB. 2005 Saeco International Group INCANTO-CLASS 8. DISASSEMBLY · · Connect the the motor to the wiring. The black wire has to be connected to (-), the white one has to be connected to (+). Fig. 12 · In case the sprocket is worn out, remove the gear, by means of a 7mm and a 10 mm fork wrench. Fig. 14 · Fasten it again using the 7mm and 10mm fork wrench. Fig. 15 Saeco International Group REV. 1 FEB. 2005 Seite 11/29 8. DISASSEMBLY INCANTO S-CLASS · Grease the gear. Fig. 16 Attention: · Use exclusivley grease type: "Interflon fin food grease 2". 18 Attention: · Make sure there is no grease on the sensor · Re-assemble. Fig. [. . . ] Dosing magnet Grinder Microswitch HWS Microswitch Door Microswitch Brewing unit Microswitch Grinds container Button Coffee +HWS Steam Control setting Cup fill volume Indicator LED Fault LED (flow meter pulses) * Coffee LED Gear switch Coffee Steam(Hot water) Coffee LED (Gear switch) Coffee Steam (Hot water) Steam LED Doser full Steam LED Fault LED flashes Fault LED flashes Fault LED flashes Saeco International Group REV. 5 FEB. 2005 Page 11/11 CHAPTER 6 FAULTS Page 1. Faults 1 Saeco International Group REV5 FEB. 2005 INCANTO S-CLASS 1. FAULTS The following table indicates the most common faults, listed by component. Part Fault Does not function (no indicator light) Cold coffee Standby LED lights up continuously Temperature differences No froth Heating remains cold Coffee and expresso LEDs flash continuously Does not function Water instead of coffee Cause HS LED defective Electronic system defective KTY defective Electronic system defective KTY defective Electronic system defective Heating - Interruption Thermal fuse defective Heating plug connection Interruption Doser switch constantly activated / Dirt Defective doser rinse Dose quantity too low Coffee residue in dosing chamber (under-dose) Doser switch does not work Electronic system defective Heating Doser Weak coffee Fault LED (coffee beans low) lights up constantly - Brewing unit overfull - Gearmotor obstructed Coffee too strong / flows too slowly Coffee too weak / flows too fast, no froth Grinder Grinder functions until fault LED (coffee beans low) lights up (insufficient beans in bean container) Grinder does not work Grinding set too finely Grind set too coarsely Grinder motor not properly installed Grinding disc worn Water in grinder Motor defective Electronic system defective Sensor defective Gear defective Page 1/3 Saeco International Group REV. 5 FEB. 2005 6. [. . . ]