User manual SONY CDP-315

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY CDP-315. We hope that this SONY CDP-315 user guide will be useful to you.


SONY CDP-315 : Download the complete user guide (2268 Ko)

Manual abstract: user guide SONY CDP-315

Detailed instructions for use are in the User's Guide.

[. . . ] Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol Y or coloured green or green-and-yellow. If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. ⷠAC power cord must be changed only at the qualified service shop. [. . . ] ⷠShould any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further. If you aren't familiar with how to play CDs, go to the section "Playing a CD" on page 6. Note that you cannot use the following functions when making this connection: · Adjusting the output level using the LINE OUT LEVEL +/­ buttons on the remote (see above) POC-15 Optical cable (not supplied) CD player Digital component When you connect via the DIGITAL OUT (OPTICAL) connector, noise may occur when you play CD software other than music, such as a CD-ROM. If you turn on the player with a CD in the tray You can start playing automatically from the beginning of the CD. If you connect a commercially available timer, you can start playing the CD at any time you want. Turn on the amplifier and select the CD player position so that you can listen to the sound from this player. You can adjust the output level with the LINE OUT LEVEL +/­ on the remote (CDP-315 and CDP-XE300 only) Z The disc tray closes and the player plays all the tracks once (Continuous Play). You can adjust the headphones volume on the remote (CDP-315 only) Z Connect the headphones to the PHONES jack and adjust the volume with the LINE OUT LEVEL +/­ on the remote. Pause Resume play after pause Go to the next track Go back to the preceding track Stop play and remove the CD You can check information about the disc using the display. While playing a disc, the display shows the current track number, playing time and the music calendar. The track numbers in the music calendar disappear after they are played. Total playing time Track numbers being programmed You can start Shuffle Play while playing Last programmed track Playing order After one second Press number buttons of the tracks you want to program in the order you want. If you've made a mistake Repeat Steps 2 and 3 to program the tracks in the order you want. When tracks, which aren't numerically consecutive on the disc, are programmed consecutively (i. After one second The program remains even after the Program Play ends when you press · , you can play the same program again. To select a track with a number over 10 The total playing time doesn't appear in the display when it exceeds 100 minutes. ⷠ"FULL" appears in the display when you try to add a track to a program which already contains 24 tracks. If you've made a mistake Press CLEAR, then press the correct track number. When tracks, which aren't numerically consecutive on the disc, are programmed consecutively (i. The program remains even after the Program Play ends When you press (, you can play the same program again. By inserting a pause during programming, you can divide the program into two for recording on both sides of a tape. You can check the total playing time while programming using the remote (Program Edit) To select a track, press = or + and check the total playing time. [. . . ] Turn AMS ± until track number you want to add appears, then press ENTER. When using the remote, press the number button of the tracks to be added (except for CDP-XE200). When you record on both sides of the tape, the player pauses at the end of the program for side A. Change the whole program completely The indication appears while checking the program for side A and while checking the program for side B. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY CDP-315




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY CDP-315 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.