User manual SONY XM-C1000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY XM-C1000. We hope that this SONY XM-C1000 user guide will be useful to you.
Manual abstract: user guide SONY XM-C1000
Detailed instructions for use are in the User's Guide.
[. . . ] * Pulsepowersupply This unit has a built-in power regulator which converts the power supplied by the 12 V DC car battery into high speed pulses using a semiconductor switch. These pulses are stepped up by the built-in pulse transformer and separated into both positive and negative power supplies before being converted into direct current again. This light weight power supply system provides a highly efficient power supply with a low impedance output. Use speakers with an impedance of 2 to 8 (4 to 8 when used as a bridging amplifier). [. . . ] Avoid installing the unit in areas subject to: -- high temperatures such as from direct sunlight or hot air from the heater -- rain or moisture -- dust or dirt. If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool down before use. When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc. If this unit is placed too close to the car audio unit or antenna, interference may occur. In this case, relocate the amplifier away from the car audio unit or antenna. If no power is being supplied to the car audio unit, check the connections. This power amplifier employs a protection circuit* to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connecting improper loads. Do not use the unit on a weak battery as its optimum performance depends on a good power supply. For safety reasons, keep your car audio unit volume moderate so that you can still hear sounds outside your car. First, place the unit where you plan to install it, and mark the positions of the 4 screw holes on the mounting board (not supplied). Then drill a 3 mm (1/8 in) pilot hole at each mark and mount the unit onto the board with the supplied mounting screws. The mounting screws are all 15 mm (19/32 in) long, so make sure that the mounting board is thicker than 15 mm (19/32 in). When you tighten the screw, be careful not to apply too much torque* as doing so may damage the screw. * The torque value should be less than 1 N· Car audio unit Autoradio Sistema de audio para automóvil less than 450 mm (18 in) moins de 450 mm (18 po) menos de 450 mm Notes In this system, the volume of the subwoofer will be controlled by the car audio unit fader control. In this system, the output signals to the subwoofer will be the combination of both the REAR L and R INPUT jacks or the REAR high level input connector signals. If *1 you have the factory original or some other car audio unit without a remote output for the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. In High level input connection, car audio unit can also be activated without need for REMOTE connection. Front right speaker output Sortie du haut-parleur avant droit Salida del altavoz delantero derecho Rear right speaker output Sortie du haut-parleur arrière droit Salida del altavoz trasero derecho Purple Mauve Violeta Car audio unit Autoradio Sistema de audio para automóvil Striped Rayé Con rayas Green Vert Verde Striped Rayé Con rayas Before making any connections, disconnect the Ground terminal of the car battery to avoid short circuits. Do not connect the terminal of the speaker system to the car chassis, and do not connect the terminal of the right speaker with that of the left speaker. [. . . ] Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. May not perform to its full potential if used with the speaker cords supplied with the car. If your car is equipped with a computer system for navigation or some other purpose, do not remove the ground wire from the car battery. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY XM-C1000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY XM-C1000 will begin.