User manual STANTON VRM-10

[. . . ] The 1/4" Jacks for EFFECT SEND, EFFECT RETURN and AUX are set as follows: TIP: LEFT RING: RIGHT SHAFT: GROUND Q GROUND connection for turntable If the connected turntable has a separate GROUND cable, it must be connected with the screw Q to prevent ground humming. R Output attenuation selector for MASTER 1 S MASTER 1 LEFT T MASTER 2 RIGHT The main output MASTER 1 is equipped with balanced (symmetrical) XLR jacks. The value of this output can be selected either at +6 or 0dBu with the switch R. The value of the output signal can also be individually set with the MASTER (51) control. [. . . ] The LFO will affect all effects, depending on the setting of the DEPTH control. 17 FACTOR With this control you can adjust the Time factor of each effect individually. The middle position of this control will have the value of the individual selected effect preset indicated in the diagram above. 18 DEPTH With this control you can adjust the intensity of the LFO 19 SELECT With this switch you can choose the channel on which the effect should work. The following 6 positions are available: MIC CH1 CH2 CH3 CH4 MA Microphone channel PGM1 PGM2 PGM3 PGM4 Master section 27 BASS 28 MIDDLE 29 MID FREQ With the EQ you can set the level of each frequency. This is very easy and effective with the high quality and very strong filter-type parametric EQ on your VRM10. NOTE : As the VRM-10's EQ is so powerful, you may have to carefully adjust the GAIN (23) while using the EQ (26-29) 30 CHANNEL FADER With the fader you can set the volume of the input channel 20 ON / OFF / FLASH With this switch you can turn the effect on or off. Therefore we will only describe PGM1: 21 SELECT With this switch you can select one of the three inputs: TT L1 L2 PHONO LINE 1 LINE 2 (M) (I) (H) The VRM10 is equipped with high quality faders. Nevertheless a fader has no life-time warranty (see warranty section) as it is used in a heavy duty way. If the fader ever needs replaced, we have made it easy to be replaced:Just loosen the 4 screws around the fader; then disconnect the fader and replace with the new part. Connect the fader back into the socket and screw the 4 screws back into their holes. 31 PFL In the headphones you will hear the signal of the master output if none of these buttons are activated: PFL (31), EFFECT (57) and FILTER (56). If you press any PFL switch you will here the selected audio signal before the master output signal. NOTE : It is possible to select more than one channel with the PFL option. CROSSFADER 32 Crossfader With the crossfader you can control and mix the various audio channels. You must have selected which channel runs through the crossfader, though. Using modern VCA-technology in the VRM10 prevents early damage of the crossfader. Nevertheless, once in a while every fader gets worn out and needs to be replaced. To change the crossfader easily you only need to unscrew the two screws on the fader and disconnect the socket. Then you need to connect the new fader and put the screws back into their place. 33/34 TRIGGER With both these buttons you can punch-in the audio signal on whichever side of the crossfader you would like to hear it, no matter in which position the crossfader is. By pressing both buttons you will hear both audio signals on either side of the crossfader. 4 22 CROSSFADER This switch will select to which side of the crossfader the the signal of the selected channel should be routed. [. . . ] 48 RETURN With this you control the volume of the external effect signal returned to the mixer. NOTE : When the internal effect (19) is turned on and set to MASTER (20), the external effect will be automatically switched off. 49 BOOTH With this you control the volume of the BOOTH output (max level is set at 0dBu). 50 BALANCE With this knob you can control the balance (pan) for the MASTER outputs. [. . . ]